Despite the unique capabilities of Additive Manufacturing (AM) processes for producing Ti components with complex geometries, the desired properties are only achievable if a holistic scheme is devised, considering the synergistic role of post-processing steps. This work aimed to enhance the applicability of metal AM products by improving the process chain in the manufacturing industry. For this purpose, the current work demonstrates a comprehensive investigation into the hot deformation of Ti-6Al-4 V (Ti64) pre-forms produced via the Electron Beam Powder Bed Fusion (EB-PBF) process focusing on the determination of critical conditions for initiating Dynamic Recrystallization (DRX) in these components. Following a sequential evaluation procedure, hot deformation experiments were carried out at temperatures ranging from 1000 to 1200 degrees C and strain rates of 0.001-1 s(-1) to determine the critical stress and strain required for initiating DRX in Ti64 pre-forms and compare them to their wrought counterparts. In addition, a specific Finite Element Model (FEM) was coupled with DRX kinetics equations to predict the volume percentage of DRX grains during the hot deformation of the pre-forms. The analysis of flow stress curves showed a significant peak stress at low strains, which is then followed by a period of flow softening and eventually transitions into a nearly steady-state flow at higher strains. In addition, compared to their wrought counterparts, the EB-PBF samples exhibited a significantly superior flow softening behavior, as evidenced by a more significant volume fraction of DRX and faster recrystallisation rates. It was also revealed that the normalised strain for DRX initiation in the EB-PBF Ti64 and wrought one was 0.55 and 0.67, respectively. FEM results closely matched the experimental finding, confirming its reliability in providing valuable insights into microstructural evolution and offering a time-efficient alternative for process design and property optimisation, lowering dependence on trial-and-error approaches. Through a combination of experiments, numerical analysis, and finite element simulations, this study sheds light on the macroscopic deformation and microstructural transformations occurring during hot working processes.

Critical condition for initiation of dynamic recrystallisation in electron beam powder bed fused Ti-6Al-4 V Alloy / Taghian, Mohammad; Mani, Hossein; Mosallanejad, Mohammadhossein; Abdi, Ata; Saboori, Abdollah; Iuliano, Luca. - In: JOURNAL OF ALLOYS AND COMPOUNDS. - ISSN 0925-8388. - 1005:(2024). [10.1016/j.jallcom.2024.176165]

Critical condition for initiation of dynamic recrystallisation in electron beam powder bed fused Ti-6Al-4 V Alloy

Taghian, Mohammad;Mosallanejad, Mohammadhossein;Saboori, Abdollah;Iuliano, Luca
2024

Abstract

Despite the unique capabilities of Additive Manufacturing (AM) processes for producing Ti components with complex geometries, the desired properties are only achievable if a holistic scheme is devised, considering the synergistic role of post-processing steps. This work aimed to enhance the applicability of metal AM products by improving the process chain in the manufacturing industry. For this purpose, the current work demonstrates a comprehensive investigation into the hot deformation of Ti-6Al-4 V (Ti64) pre-forms produced via the Electron Beam Powder Bed Fusion (EB-PBF) process focusing on the determination of critical conditions for initiating Dynamic Recrystallization (DRX) in these components. Following a sequential evaluation procedure, hot deformation experiments were carried out at temperatures ranging from 1000 to 1200 degrees C and strain rates of 0.001-1 s(-1) to determine the critical stress and strain required for initiating DRX in Ti64 pre-forms and compare them to their wrought counterparts. In addition, a specific Finite Element Model (FEM) was coupled with DRX kinetics equations to predict the volume percentage of DRX grains during the hot deformation of the pre-forms. The analysis of flow stress curves showed a significant peak stress at low strains, which is then followed by a period of flow softening and eventually transitions into a nearly steady-state flow at higher strains. In addition, compared to their wrought counterparts, the EB-PBF samples exhibited a significantly superior flow softening behavior, as evidenced by a more significant volume fraction of DRX and faster recrystallisation rates. It was also revealed that the normalised strain for DRX initiation in the EB-PBF Ti64 and wrought one was 0.55 and 0.67, respectively. FEM results closely matched the experimental finding, confirming its reliability in providing valuable insights into microstructural evolution and offering a time-efficient alternative for process design and property optimisation, lowering dependence on trial-and-error approaches. Through a combination of experiments, numerical analysis, and finite element simulations, this study sheds light on the macroscopic deformation and microstructural transformations occurring during hot working processes.
File in questo prodotto:
File Dimensione Formato  
1-s2.0-S092583882402752X-main_compressed.pdf

accesso aperto

Tipologia: 2a Post-print versione editoriale / Version of Record
Licenza: Creative commons
Dimensione 1.19 MB
Formato Adobe PDF
1.19 MB Adobe PDF Visualizza/Apri
Pubblicazioni consigliate

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11583/2992403