The power exhaust concept and an appropriate divertor design are common critical issues for tokamak DEMO design activities which have been carried out in Europe, Japan, China, Korea and the USA. Conventional divertor concepts and power exhaust studies for recent DEMO designs (Pfusion = 1 – 2 GW, Rp = 7 – 9 m) are reviewed from the viewpoints of the plasma physics issues and the divertor engineering design. Radiative cooling is a common approach for the power fusion scenario. Requirements on the main plasma radiation fraction (frad main = Prad main/Pheat) and the plasma performance constrain the divertor design concept. Different challenges contribute to optimizing the future DEMO designs: for example, (i) increasing the main plasma radiation fraction for ITER level Psep/Rp designs and simplifying the divertor geometry, and (ii) extending ITER divertor geometry with increasing divertor radiation (Prad div) for larger Psep/Rp ≥ 25MWm− 1 designs. Power exhaust simulations with large Psep = 150 – 300 MW have been performed using integrated divertor codes considering an ITER-based divertor geometry with longer leg length (1.6 – 1.7 m), as in a common baseline design. Geometry effects (ITER like geometry or more open one without baffle) on the plasma detachment profile and the required divertor radiation fraction (frad div = Prad div/Psep) were key aspects of these studies. All simulations showed that the divertor plasma detachment were extended widely across the target plate with a reduction in the peak heat load of qtarget ≤ 10 MWm− 2 for the large frad div = 0.7 – 0.8, while the peak qtarget location and value were noticeably different in the partially detached divertor. Simulation results also demonstrated that radial diffusion coefficients of the heat and particle fluxes were critical parameters for DEMO divertor design, and that effects of plasma drifts on outboard enhanced asymmetry of the heat flux, suggested the need for longer divertor leg to ensure the existence of a detached divertor operation with qtarget ≤ 10 MWm− 2 . Integrated design of the water cooled divertor target, cassette body (CB) and cooling pipe routing has been developed for each DEMO concept, based on the ITER-like tungsten monoblock (W-MB) with Cu-alloy cooling pipes. Engineering design adequate under higher neutron irradiation condition was required. Therefore, inlet coolant temperature (Tcool) was increased. In current designs, it still shows a large potential variation between 70 ◦C and 200 ◦C. The influence of thermal softening on the Cu-alloy (CuCrZr) pipe was fostered near the strike point when the high qtarget of ~10 MWm− 2 was studied. Improved technologies for high heat flux components based on the ITER W-MB unit have been developed for EU-DEMO. Different coolant conditions (low- and high Tcool) were provided for Cu-alloy and reduced activation ferritic martensitic (RAFM) steel heat sink units, respectively. The high-Tcool coolant was also considered for the CB and supporting structures. Appropriate conditions for the high-Tcool coolant, i.e. 180 ◦C/ 5 MPa (EU-DEMO) and 290 ◦C/ 15 MPa (JA-DEMO, CFETR and K-DEMO), will be determined in the future optimizations of the divertor and DEMO design.

Recent progress of plasma exhaust concepts and divertor designs for tokamak DEMO reactors / Asakura, N.; Hoshino, K.; Kakudate, S.; Subba, F.; You, J. -H.; Wiesen, S.; Rognlien, T. D.; Ding, R.; Kwon, S.. - In: NUCLEAR MATERIALS AND ENERGY. - ISSN 2352-1791. - ELETTRONICO. - 35:(2023). [10.1016/j.nme.2023.101446]

Recent progress of plasma exhaust concepts and divertor designs for tokamak DEMO reactors

Subba F.;
2023

Abstract

The power exhaust concept and an appropriate divertor design are common critical issues for tokamak DEMO design activities which have been carried out in Europe, Japan, China, Korea and the USA. Conventional divertor concepts and power exhaust studies for recent DEMO designs (Pfusion = 1 – 2 GW, Rp = 7 – 9 m) are reviewed from the viewpoints of the plasma physics issues and the divertor engineering design. Radiative cooling is a common approach for the power fusion scenario. Requirements on the main plasma radiation fraction (frad main = Prad main/Pheat) and the plasma performance constrain the divertor design concept. Different challenges contribute to optimizing the future DEMO designs: for example, (i) increasing the main plasma radiation fraction for ITER level Psep/Rp designs and simplifying the divertor geometry, and (ii) extending ITER divertor geometry with increasing divertor radiation (Prad div) for larger Psep/Rp ≥ 25MWm− 1 designs. Power exhaust simulations with large Psep = 150 – 300 MW have been performed using integrated divertor codes considering an ITER-based divertor geometry with longer leg length (1.6 – 1.7 m), as in a common baseline design. Geometry effects (ITER like geometry or more open one without baffle) on the plasma detachment profile and the required divertor radiation fraction (frad div = Prad div/Psep) were key aspects of these studies. All simulations showed that the divertor plasma detachment were extended widely across the target plate with a reduction in the peak heat load of qtarget ≤ 10 MWm− 2 for the large frad div = 0.7 – 0.8, while the peak qtarget location and value were noticeably different in the partially detached divertor. Simulation results also demonstrated that radial diffusion coefficients of the heat and particle fluxes were critical parameters for DEMO divertor design, and that effects of plasma drifts on outboard enhanced asymmetry of the heat flux, suggested the need for longer divertor leg to ensure the existence of a detached divertor operation with qtarget ≤ 10 MWm− 2 . Integrated design of the water cooled divertor target, cassette body (CB) and cooling pipe routing has been developed for each DEMO concept, based on the ITER-like tungsten monoblock (W-MB) with Cu-alloy cooling pipes. Engineering design adequate under higher neutron irradiation condition was required. Therefore, inlet coolant temperature (Tcool) was increased. In current designs, it still shows a large potential variation between 70 ◦C and 200 ◦C. The influence of thermal softening on the Cu-alloy (CuCrZr) pipe was fostered near the strike point when the high qtarget of ~10 MWm− 2 was studied. Improved technologies for high heat flux components based on the ITER W-MB unit have been developed for EU-DEMO. Different coolant conditions (low- and high Tcool) were provided for Cu-alloy and reduced activation ferritic martensitic (RAFM) steel heat sink units, respectively. The high-Tcool coolant was also considered for the CB and supporting structures. Appropriate conditions for the high-Tcool coolant, i.e. 180 ◦C/ 5 MPa (EU-DEMO) and 290 ◦C/ 15 MPa (JA-DEMO, CFETR and K-DEMO), will be determined in the future optimizations of the divertor and DEMO design.
File in questo prodotto:
File Dimensione Formato  
Asakura2023-1-10_compressed.pdf

accesso aperto

Descrizione: parte 1
Tipologia: 2a Post-print versione editoriale / Version of Record
Licenza: Creative commons
Dimensione 9.43 MB
Formato Adobe PDF
9.43 MB Adobe PDF Visualizza/Apri
Asakura2023-11-19_compressed.pdf

accesso aperto

Descrizione: parte 2
Tipologia: 2a Post-print versione editoriale / Version of Record
Licenza: Creative commons
Dimensione 9.25 MB
Formato Adobe PDF
9.25 MB Adobe PDF Visualizza/Apri
Pubblicazioni consigliate

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11583/2981024