The current study was oriented at analyzing the performance of an anode-supported solid oxide fuel cell produced using high-pressure injection molding. The cell with a total thickness of 550 μm was produced in the Ceramic Department (CEREL) of the Institute of Power Engineering in Poland and experimentally analyzed in the Energy Department (DENERG) of Politecnico di Torino in Italy. The high-pressure injection molding technique was applied to produce a 500 μm thick anode support NiO/8YSZ 66/34 wt% with porosity of 25 vol%. The screen printing method was used to print a 3 μm thick NiO anode contact layer, 7 μm thick NiO/8YSZ 50/50 wt% anode functional layer, 4 μm thick 8YSZ dense electrolyte, 1.5 μm thick Gd0,1Ce0,9O2 barrier layer and a 30 μm thick La0,6Sr0,4Fe0,8Co0,2O3–δ cathode with porosity 25 vol%. The experimental characterization was done at two temperature levels: 750 and 800 °C under fixed anodic and cathodic flow and compositions. The preliminary studies on the application of high-pressure injection molding are discussed together with the advantages of the technology. The performance of two generations of anode-supported cells is compared with data of reference cells with supports obtained using tape casting.

Characterization of a circular 80 mm anode supported solid oxide fuel cell (AS-SOFC) with anode support produced using high-pressure injection molding (HPIM) / Kupecki, Jakub; Kluczowski, Ryszard; Papurello, Davide; Lanzini, Andrea; Kawalec, Michał; Krauz, Mariusz; Santarelli, Massimo. - In: INTERNATIONAL JOURNAL OF HYDROGEN ENERGY. - ISSN 0360-3199. - ELETTRONICO. - (2019). [10.1016/j.ijhydene.2018.02.143]

Characterization of a circular 80 mm anode supported solid oxide fuel cell (AS-SOFC) with anode support produced using high-pressure injection molding (HPIM)

Papurello, Davide;Lanzini, Andrea;Santarelli, Massimo
2019

Abstract

The current study was oriented at analyzing the performance of an anode-supported solid oxide fuel cell produced using high-pressure injection molding. The cell with a total thickness of 550 μm was produced in the Ceramic Department (CEREL) of the Institute of Power Engineering in Poland and experimentally analyzed in the Energy Department (DENERG) of Politecnico di Torino in Italy. The high-pressure injection molding technique was applied to produce a 500 μm thick anode support NiO/8YSZ 66/34 wt% with porosity of 25 vol%. The screen printing method was used to print a 3 μm thick NiO anode contact layer, 7 μm thick NiO/8YSZ 50/50 wt% anode functional layer, 4 μm thick 8YSZ dense electrolyte, 1.5 μm thick Gd0,1Ce0,9O2 barrier layer and a 30 μm thick La0,6Sr0,4Fe0,8Co0,2O3–δ cathode with porosity 25 vol%. The experimental characterization was done at two temperature levels: 750 and 800 °C under fixed anodic and cathodic flow and compositions. The preliminary studies on the application of high-pressure injection molding are discussed together with the advantages of the technology. The performance of two generations of anode-supported cells is compared with data of reference cells with supports obtained using tape casting.
File in questo prodotto:
Non ci sono file associati a questo prodotto.
Pubblicazioni consigliate

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11583/2728438
 Attenzione

Attenzione! I dati visualizzati non sono stati sottoposti a validazione da parte dell'ateneo